PLC sequence and machine states
Translate the agreed process into explicit states, transitions, permissives, alarms and recovery behavior. The final sequence should be reviewed against the machine's actual operating procedure.
Industrial Automation Products · Engineering Services · Quote Support
Utilities
Compressor Automation
Compressor automation can coordinate run requests, available pressure feedback and equipment status according to the compressor and air-system design. Automation scope depends on the equipment, operating sequence, existing controls and process requirements. Share the machine details and desired outcome to define a suitable control approach.
Application overview
Compressor automation can coordinate run requests, available pressure feedback and equipment status according to the compressor and air-system design.
Typical requirements to define
- Compressor type and installed controller interface
- Pressure measurement and required operating band
- Lead/standby or sequencing needs
- Permissives, alarms and restart conditions
Example process sequence
- Check system demand and compressor readiness
- Issue a permitted run request or sequence command
- Monitor available pressure and equipment status
- Coordinate standby equipment if defined in the system scope
- Handle faults and restart only under documented conditions
Pump duty and pressure control
A control sequence can select lead or standby equipment, monitor pressure feedback and apply run permissives and alarms. PID and VFD control are suitable only where the pump, drive and hydraulic arrangement support them.
Operator interface and alarms
An HMI may show mode, step, status, setpoints and actionable alarm information. Screen behavior and operator permissions should match the plant's procedures.
Motor drives and instrumentation
Where installed equipment supports it, drives can be controlled through suitable hardwired or network interfaces. Sensors and transmitters should be selected and scaled to the machine and process requirements.
Safety and fault handling
Safety functions must be designed for the risk assessment and applicable machine requirements. Standard PLC logic should not be treated as a substitute for safety-rated hardware or a validated safety design.
Pressure band and equipment protection
Pressure targets, unloading behavior, start limits and minimum off times must respect compressor manufacturer requirements and the system design.
Related automation technologies
Explore the control systems that may be relevant to this scope.
Products from the catalog
These active catalog products are related by their existing category. Confirm model compatibility and availability for your application.
PLC
Siemens S7-1200 CPU 1214C DC/DC/DC PLC – 14DI/10DO/2AI, 6ES7214-1AG40-0XB0
Siemens S7-1200 CPU 1214C DC/DC/DC PLC with 14 digital inputs, 10 digital transistor outputs and 2 analog inputs. 24 V DC supply, 150 KB program/data memory and PROFINET communication.
Industrial Communication
RS232 PLC HMI Communication Cable – DB9 Serial Programming Cable for Industrial Automation
RS232 serial communication cable for compatible PLCs and HMIs, suitable for programming, configuration, commissioning, diagnostics and industrial automation communication.
HMI
Delta DOP-107CV 7 Inch Touchscreen HMI – 800×480 TFT, RS-232/RS-485/RS-422, USB
Delta DOP-107CV 7-inch industrial touchscreen HMI with 800×480 resolution, 65,536-color TFT display, 256 MB RAM/ROM, RS-232/RS-485/RS-422 communication, USB Host/Client, and 24 VDC power supply.
PLC
Delta DVP28SV11T2 PLC – DVP-SV2 Series, 16 Digital Inputs, 12 Transistor Outputs, 24V DC
Delta DVP28SV11T2 DVP-SV2 Series high-performance slim PLC with 16 digital inputs and 12 NPN transistor outputs. Featuring high-speed processing, high-speed counters and pulse outputs, it is suitable for machine automation, motion control, packaging, printing, conveyor and industrial control applications
PLC
Delta DVP12SA2 PLC – DVP-SA2 Advanced Slim PLC, 8DI/4DO, 24VDC, RS-232/RS-485
Delta DVP12SA2 DVP-SA2 Advanced Slim PLC with 8 digital inputs, 4 digital outputs, 24VDC supply, 16K steps and RS-232/RS-485 Modbus communication.
PLC
Delta DVP60ES200R PLC – DVP-ES2, 36DI/24 Relay Output, 16K Steps
Delta DVP60ES200R DVP-ES2 PLC with 36 digital inputs, 24 relay outputs, 100–240VAC power supply and 16K-step program capacity for industrial automation.
PLC
Delta DTC1000 Temperature Controller – 24VDC, PID/ON-OFF Control, RS-485 Modbus
Delta DTC1000 modular temperature controller with 24VDC supply, PID/ON-OFF control, multiple sensor inputs and RS-485 Modbus communication.
PLC
Delta DVP14SS211R PLC – DVP-SS2 Slim PLC, 8DI/6 Relay Outputs, 24VDC, RS-232/RS-485
Delta DVP14SS211R DVP-SS2 Slim PLC with 8 digital inputs, 6 relay outputs, 24VDC supply, RS-232/RS-485 communication and Modbus support.
Related engineering services
PLC programming
Discuss the equipment, existing controls and project requirements with our engineering team.
Request service quote →HMI programming
Discuss the equipment, existing controls and project requirements with our engineering team.
Request service quote →Machine automation
Discuss the equipment, existing controls and project requirements with our engineering team.
Request service quote →Related applications and topics
Frequently asked questions
What information is useful for a compressor automation enquiry?
Describe the machine or process, current controls, operating sequence, required modes, available drawings and the changes you want to make. Include known controller and drive models where possible.
Can existing equipment be considered?
Yes. Include the installed controller, HMI, drives, sensors and any drawings or fault details so the existing arrangement can be reviewed before defining scope.
Discuss your automation requirements
Share the equipment details, current controls and process sequence for a scope review.